hey the prong on the red cable is way shorter than the white one i dont experience how it happened but i notice this turntable has more hum on it or wants to " clip" alot more on the mixer.. it fits loosely on the end of my vestax pmc 07 pro still goes in tho i've usin it so far i'm able to do ok but i'm not sure if the clippin has somethin to do with this and if i should get it replaced only problem is this telecommunicate is already connected to the turntable cant' plug it in or out of the turntable.. soo i dunno how to go about this,.. thanks for any replies!
hey the prong on the red cable is way shorter than the white one i dont know how it happened but i notice this turntable has more hum on it or wants to " clip" alot more on the mixer.. it fits loosely on the end of my vestax pmc 07 pro still goes in tho i've usin it so far i'm able to do ok but i'm not sure if the clippin has somethin to do with this and if i should get it replaced only problem is this telecommunicate is already connected to the turntable cant' close it in or out of the turntable.. soo i dunno how to go about this,.. thanks for any replies!
get yourself a stanton str8-150 with detachable rca's! No soldering required!lol! But yer just replace the rca's they sometimes get bent and misshaped under use.
__________________2X Stanton str8-150's. 2X Technics 1200's- 4X m447'sPioneer DJM 909. DJM 707MPC 2500. Soundcraft Compact 10
Just get a new cable i have literally about 50 I don't use. (I use em as replacements repairs etc...)
but is your telecommunicate already attached to the table where it move be removed that's my problem and i dont know how to solder.. kirk
but is your cable already attached to the table where it move be removed that's my problem and i dont know how to solder.. kirk
Soldering is VERY easy. Buy an iron and a roll of solder from radio shack. You're after a 15 watt iron and rub core out solder. 0.035 (0.5mm) or similar coat on the solder. Thinner solder allows you to act the joint cooler and solder it a bit faster before anything can melt if you're doing up a RCA end. The process is very simple. Touch tip to joint you're soldering. Allow a couple seconds to heat up touch solder to joint allow it to move Don't put too much into the joint or get it too hot you wouldn't wanna melt anything too badly. Another solution to this issue would be to upgrade to a exceed be. Ditch the Gemini(s) after you fix this and have some cash saved up.
^^they're actually great technics alternatives(i own one)only complaint is the built material for the cabinet..(wish it could have the aluminum diecast cabinet like the 1200s
To get te crap out or off of your connections (as I say crap I mean the plugs) just take a needle nose plier and gently pull/twist it out/off.
Monster cables are a ripoff and are outperformed by cables 1/10 of their price. And they won't guarantee a cable that has been modified for the sole purpose to fit a TT. You be real cable quality for your $ ? Get AudioQuest cables.
no worries man. It's the sad truth. I did a lot of side to side comparisons with high end cables at a friends' hifi shop. it turned out Monster is garbage seriously. beat moment: we tried a $250 monster rca cable against a $40 Profigold Rca cable. The result was a valuable lesson on how to save 200 and 10 bucks... I use AudioQuest cables. ( CopperHead for interconnects and StarQuad CV4 for speakers) they're quite expensive but you get some quality for your hard earned cash. And they should last for quite some time..
Forex Groups - Tips on Trading
Related article:
http://www.djforums.com/forums/showthread.php?t=120670
comments | Add comment | Report as Spam
|
